val const : string -> _ t
const s is the segment that always displays
const, but takes a format string and corresponding arguments.
constf "..." a b c ... is equivalent to
const (Format.asprintf "..." a b c ...), except that colours added with
Fmt.styled are not discarded.
val string : string t
lpad n t left-pads the segment
t to size
n by adding blank space at the start.
rpad n t right-pads the segment
t to size
n by adding blank space at the end.
of_printer p is a segment that renders the latest reported value using printer
sum for a variant that reports accumulated values instead.
These segments all consume integer values and display the accumulated total of reported values in some way. The top-level
Line segments are specialised to
int values; see "Alternative integer types" for variants supporting
count_to target renders both the current running total of reported values and the fixed value
target, separated by the the given separator, i.e.
sep defaults to
Prints the running total as a number of bytes, using ISO/IEC binary prefixes (e.g.
10.4 MiB). See also
percentage_of target renders the running total as a percentage of
42%. Values outside the range
[0, 100] will be clamped to either
sum ~width () displays a running total of reported values using
width-many terminal columns. If passed,
pp overrides the printer used for rendering the count.
module Bar_style : sig ... end
val bar : ?style:[ `ASCII | `UTF8 | `Custom of Bar_style.t ] -> ?color:Color.t -> ?width:[ `Fixed of int | `Expand ] -> ?data:[ `Sum | `Latest ] -> integer -> integer t
bar total is a progress bar of the form:
The proportion of the bar that is filled is given by
<reported_so_far> / total. Optional parameters are as follows:
?stylespecifies whether to use a UTF-8 or an ASCII encoding for the progress bar. The UTF-8 encoding shows a higher resolution of progress, but may not be supported in all terminals. The default is
?colorcauses the filled portion of the bar to be rendered with the given colour. (Equivalent to setting the colour with
?widthis the width of the bar in columns. Defaults to
`Expand, which causes the bar to occupy the remaining rendering space after accounting for other line segments on the same line.
?datachanges the metric that is indicated by the progress bar.
`Sum(the default) causes the progress bar to correspond to the running total of values reported so far.
`Latestcauses each reported value to overwrite the previous one instead.
val spinner : ?frames:string list -> ?color:Color.t -> ?min_interval:Duration.t option -> unit -> _ t
spinner () is a small segment that cycles over a fixed number of frames each time a value is reported. e.g.
⠋ → ⠙ → ⠹ → ⠸ → ⠼ → ⠴ → ⠦ → ⠧ → ⠇ → ⠏ → ...
Optional prameters are as follows:
?framesalters the sequence of frames rendered by the spinner;
?colorcauses each frame to be rendered with the given colour;
?min_intervalis the minimum time interval between frame transitions of the spinner (i.e. a debounce threshold). The default is
bytes_per_sec renders the rate of change of the running total as a number of bytes per second, using ISO/IEC binary prefixes (e.g.
Displays the time for which the bar has been rendering in
Displays an estimate of the remaining time until
total is accumulated by the reporters, in
rate pp is an integer segment that uses
pp to print the rate of reported values per second. (For instance,
Horizontally join a list of segments, with a given separator.
sep defaults to
const " ".
Horizontally join a pair of segments consuming different reported values into a single segment that consumes a pair.
using f s is a segment that first applies
f to the reported value and then behaves as segment
The following line segments are definable in terms of the others, but provided for convenience:
val noop : unit -> _ t
A zero-width line segment that does nothing. This segment will not be surrounded with separators when used in a
list, making it a useful "off" state for conditionally-enabled segments.
val spacer : int -> _ t
spacer n is
const (String.make n ' ').